Miller Millermatic 180 MIG with Spoolmate 100 (907312)
Here's an all-in-one that can handle 24 gauge - 5/16 in (0.8-7.9mm) mild steel. Better yet, this Millermatic 180 MIG Welder with Auto-Set includes a Spoolmate 100 Spoolgun.
Auto-Set
A breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG minus the guesswork! Simply set the wire diameter, set the material thickness and start welding!
Welds Thickest Material in its Class
With the highest output in its class, the Millermatic 180 can weld up to 5/16 in. in a single pass.
Thermal Overload Protection
Shuts down the unit and activates an over-temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.
Spool Gun Compatible
Finally a reliable and economical way to weld aluminum. Hooked up to a 180 Auto-Set, the Spoolmate 100 Series spool gun allows you to weld from 18 gauge to 1/4 in. aluminum.
Manual Mode
Gives you the flexibility to manually set the machine when welding aluminum, stainless steel or anytime you want to set your own parameters on mild steel.
Smooth-Start
This technology provides a smooth, spatter-free start. The best starting machine in the small MIG category! No more pop-gun starts or spatter to clean up.
Durable Cast Aluminum Drive System
Incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob, all designed to make setup easier and faster.
Tip Saver' Short Circuit Protection
Shuts down output when tip is shorted to the work, extending contact tip life and protecting internal components from damage. Trigger reset permits quick reset at torch rather than unit.
Comes complete with:
• Millermatic 180 power source
• Spoolmate 100 Spoolgun
• 6 ft (1.8 m) power cord and plug
• 10 ft (3 m), M-100 MIG gun and cable assembly
• 10 ft (3 m) work cable and clamp
• Smith Argon and AR/CO2 mix regulator/flowgauge with hose
• Spool of Hobart .030 in (0.8 mm) solid wire
• Two contact tips for .024 in (0.6 mm) wire and two contact tips for .030 in (0.8 mm) solid wire
• Dual-groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) solid wire
• Factory-installed gas solenoid valve
• Information/settings chart
Auto-Set
A breakthrough control that automatically sets your welder to the proper parameters. Auto-Set offers all-in-one MIG minus the guesswork! Simply set the wire diameter, set the material thickness and start welding!
Welds Thickest Material in its Class
With the highest output in its class, the Millermatic 180 can weld up to 5/16 in. in a single pass.
Thermal Overload Protection
Shuts down the unit and activates an over-temperature light if airflow is blocked or duty cycle is exceeded. Automatically resets when fault is corrected and unit cools.
Spool Gun Compatible
Finally a reliable and economical way to weld aluminum. Hooked up to a 180 Auto-Set, the Spoolmate 100 Series spool gun allows you to weld from 18 gauge to 1/4 in. aluminum.
Manual Mode
Gives you the flexibility to manually set the machine when welding aluminum, stainless steel or anytime you want to set your own parameters on mild steel.
Smooth-Start
This technology provides a smooth, spatter-free start. The best starting machine in the small MIG category! No more pop-gun starts or spatter to clean up.
Durable Cast Aluminum Drive System
Incorporates dual groove quick-change drive roll and spring-loaded tension arm with calibrated tension knob, all designed to make setup easier and faster.
Tip Saver' Short Circuit Protection
Shuts down output when tip is shorted to the work, extending contact tip life and protecting internal components from damage. Trigger reset permits quick reset at torch rather than unit.
Comes complete with:
• Millermatic 180 power source
• Spoolmate 100 Spoolgun
• 6 ft (1.8 m) power cord and plug
• 10 ft (3 m), M-100 MIG gun and cable assembly
• 10 ft (3 m) work cable and clamp
• Smith Argon and AR/CO2 mix regulator/flowgauge with hose
• Spool of Hobart .030 in (0.8 mm) solid wire
• Two contact tips for .024 in (0.6 mm) wire and two contact tips for .030 in (0.8 mm) solid wire
• Dual-groove quick-change drive roll for .024 in (0.6 mm) or .030/.035 in (0.8/0.9 mm) solid wire
• Factory-installed gas solenoid valve
• Information/settings chart
| MPN: | MIL907312, MIL300371 |
|---|
MPN: MIL907312, MIL300371
Brands you trust at prices you can afford!
Over the past decade, we've become the country's most trusted one-stop online welding shop. We've done it with the guaranteed lowest prices, the best customer service in the industry, and a commitment to providing the best online shopping experience for all welders.
------------------------------
From The Blog
Guide
How to Set Up a Lincoln MIG Welder
Thinking about getting yourself a Lincoln MIG welder? Or maybe you’ve already purchased one and are stoked to lay some beads. Knowing the right way to set up your machine can save you a massive amo...
MIG
Setting up Your Millermatic 211
So, the big Miller box you've been waiting for has finally arrived at your doorstep. Now that the Millermatic 211 is in your hands, how do you set it up? Don't worry; we're here to help you get eve...
MIG
What Gas to Use When MIG Welding
How ironic is it that metal can withstand incredible pressures and high impacts like no other type of material, but its weakness is air and moisture. If your MIG weld is exposed to these elements, ...