Miller Spectrum 375 Plasma Cutter (907532)
The Miller Spectrum 375 Plasma Cutter with XT30C Torch cuts 3/8" mild steel and has dual 115/230 volt input ower capability.
Rated Cutting Capacity
The rated cutting capacity is based on traveling approximately 15 inches per minute to achieve a steady, precise cut. This is the key rating that should meet or exceed your typical cutting thickness requirements.
XT30C Torch
The XT30C torch with ergonomic handle prevents operator fatigue while the flexible cable makes maneuvering easier.
Electronic Pilot Arc Controller
Automatically controls the pilot circuit to provide expanded metal cutting ability without having to re-trigger the torch, increasing productivity and extending tip life.
Post Flow Cooling Circuit
Protection to extend the life of consumables and the welding torch is enhanced by our post flow circuit that provides shielding gas after you release the trigger.
LVC Line Voltage Compensation
LVC provides peak performance power under variable conditions (98 to 132 volts) for steady cuts and cleaner ending cuts.
Dual Input Voltage
A switch located in the back of the unit allows connection to either 115 or 230 VAC input power and provides protection in case of incorrect switch positioning. The unit comes with a standard 115V 20A plug. Connection to 115V 15A and 230V receptacles require customer supplied plugs/adapters (not included).
Built-In Consumables Storage
Built-in consumables storage compartment provides convenient access to spare consumables and parts.
Can Be Powered by Miller Engine Driven Generators
Can be powered by any Miller engine drive with generator power output of 2 kW or more, such as the Bobcat, Trailblazer or equivalent competitive equipment.
Rated Cutting Capacity
The rated cutting capacity is based on traveling approximately 15 inches per minute to achieve a steady, precise cut. This is the key rating that should meet or exceed your typical cutting thickness requirements.
XT30C Torch
The XT30C torch with ergonomic handle prevents operator fatigue while the flexible cable makes maneuvering easier.
Electronic Pilot Arc Controller
Automatically controls the pilot circuit to provide expanded metal cutting ability without having to re-trigger the torch, increasing productivity and extending tip life.
Post Flow Cooling Circuit
Protection to extend the life of consumables and the welding torch is enhanced by our post flow circuit that provides shielding gas after you release the trigger.
LVC Line Voltage Compensation
LVC provides peak performance power under variable conditions (98 to 132 volts) for steady cuts and cleaner ending cuts.
Dual Input Voltage
A switch located in the back of the unit allows connection to either 115 or 230 VAC input power and provides protection in case of incorrect switch positioning. The unit comes with a standard 115V 20A plug. Connection to 115V 15A and 230V receptacles require customer supplied plugs/adapters (not included).
Built-In Consumables Storage
Built-in consumables storage compartment provides convenient access to spare consumables and parts.
Can Be Powered by Miller Engine Driven Generators
Can be powered by any Miller engine drive with generator power output of 2 kW or more, such as the Bobcat, Trailblazer or equivalent competitive equipment.
| MPN: | MIL907532 |
|---|---|
| UPC: | 715959304306 |
MPN: MIL907532
UPC: 715959304306
Brands you trust at prices you can afford!
Over the past decade, we've become the country's most trusted one-stop online welding shop. We've done it with the guaranteed lowest prices, the best customer service in the industry, and a commitment to providing the best online shopping experience for all welders.
------------------------------
From The Blog
Guide
The Welding Hazards No One Talks About
Howard had been welding for more than a decade. But tonight, he was at home, watching a movie with his wife on the couch. In the movie, a background character picked up a welding torch and struck a...
cutting
The Right Way to Start Your Plasma Cuts
“Plasma cutting” and “good plasma cutting” are two entirely different things. “Plasma cutting” is almost as simple as not pointing the nozzle at your face and pulling the trigger. But plasma cuttin...
TIG
The Ultimate Review of the Square Wave TIG 200
Flagships: Some people think they’re just cursed. The Titanic was the flagship meant to change how we traveled the seas. The Hindenberg was a flagship meant to change how we traveled the skies.
So ...